Miscellaneous

Measuring Temperature with a Thermistor on Raspberry Pi

In this project, we will focus on Measuring Temperature with a Thermistor on Raspberry Pi. A thermistor is a temperature-sensitive resistor, and by using an MCP3008 Analog-to-Digital Converter (ADC), we can read the thermistor’s output through the Raspberry Pi. This project is perfect for beginners wanting to learn about temperature measurement and how to use analog sensors with Raspberry Pi.

Purpose of the Project 

The goal of this project is to demonstrate how to set up a simple temperature monitoring system by Measuring Temperature with a Thermistor on Raspberry Pi. You will learn to connect the hardware, install necessary libraries, and write Python code to interpret temperature readings.

Data Types and Variable Table for Measuring Temperature with a Thermistor on Raspberry Pi 

Variable Name Data Type Description
THERMISTOR_PIN Integer MCP3008 channel where the thermistor is connected
adc_value Integer Digital output value from the thermistor
temperature Float Calculated temperature based on thermistor readings

Syntax Table for Measuring Temperature with a Thermistor 

Topic Syntax Simple Example
SPI Initialization mcp = MCP3008(SPI) mcp = MCP3008(SPI.SpiDev(0, 0))
ADC Channel Reading mcp.read_adc(channel) adc_value = mcp.read_adc(0)
Print Value print(f”text: {variable}”) print(f”ADC Value: {adc_value}”)
Sleep Function time.sleep(seconds) time.sleep(1)

Required Components 

To build this project for Measuring Temperature with a Thermistor on Raspberry Pi, you will need:

  • Raspberry Pi (any model)
  • Thermistor
  • MCP3008 ADC
  • 10kΩ Resistor
  • Jumper Wires
  • Breadboard

Circuit Connection Table for Measuring Temperature with a Thermistor on Raspberry Pi 

Component Raspberry Pi Pin MCP3008 Pin Additional Notes
Thermistor – Channel 1 (CH1) Connected in series with the 10kΩ resistor
MCP3008 Pin 1 (VDD) 3.3V (Pin 1) – Powers the MCP3008 from the Raspberry Pi’s 3.3V rail
MCP3008 Pin 2 (VREF) 3.3V (Pin 1) – Reference voltage
MCP3008 Pin 3 (AGND) GND (Pin 6) – Ground for analog circuits
MCP3008 Pin 8 (DGND) GND (Pin 6) – Ground for digital circuits
MCP3008 Pin 7 (CS/SHDN) GPIO8 (Pin 24) – Connect to the Chip Select pin

Warning 

  • Always double-check the connections before powering up your Raspberry Pi.
  • Make sure the thermistor is properly connected to avoid inaccurate temperature readings.

Circuit Analysis for Measuring Temperature 

The thermistor acts as a temperature-dependent resistor, meaning its resistance varies with temperature. By measuring the voltage drop across the thermistor with the MCP3008 ADC, we can calculate the temperature. The Raspberry Pi reads the digital output of the ADC and converts it into a temperature value.

Installing Libraries 

To interface the MCP3008 with the Raspberry Pi, install the Adafruit CircuitPython library:

sudo pip3 install adafruit-circuitpython-mcp3xxx

Writing the Code Using Python 

Here’s the Python code to measure temperature using a thermistor:

import time

import Adafruit_GPIO.SPI as SPI

import Adafruit_MCP3008

 

# MCP3008 Setup

SPI_PORT = 0

SPI_DEVICE = 0

mcp = Adafruit_MCP3008.MCP3008(spi=SPI.SpiDev(SPI_PORT, SPI_DEVICE))

 

# Thermistor connected to CH1

THERMISTOR_PIN = 1

 

def calculate_temperature(adc_value):

    # Convert ADC value to temperature (simplified for this project)

    voltage = adc_value * 3.3 / 1023

    resistance = (10000 * voltage) / (3.3 – voltage)

    temperature = 1 / (0.001129148 + (0.000234125 * (resistance / 10000))) – 273.15

    return temperature

 

try:

    while True:

        # Read the thermistor value

        adc_value = mcp.read_adc(THERMISTOR_PIN)

        

        # Calculate temperature

        temperature = calculate_temperature(adc_value)

        

        # Print the temperature

        print(f”Temperature: {temperature:.2f}°C”)

        

        time.sleep(1)

 

except KeyboardInterrupt:

    print(“Program stopped”)

 

Explanation of the Code 

  • SPI Setup: Initializes the SPI interface for communication with the MCP3008.
  • Thermistor Value: The mcp.read_adc() function reads the analog value from the thermistor on Channel 1.
  • Temperature Calculation: The function calculate_temperature() converts the ADC value into a temperature reading.
  • Print Temperature: The measured temperature is displayed in degrees Celsius on the console.

Running the Code and Checking Output 

  1. Save the code as thermistor_temperature.py.

Run the script using the following command:
bash
Copy code
python3 thermistor_temperature.py

  1. Observe the temperature readings displayed in the terminal.

Expanding the Project 

You can expand this project by:

  • Logging temperature data over time for analysis.
  • Sending temperature alerts when the temperature exceeds a certain threshold.
  • Displaying the temperature on an LCD screen for a more interactive project.

Common Problems and Solutions 

  • Problem: Incorrect temperature readings.
    • Solution: Check the thermistor wiring and make sure it is correctly connected to the MCP3008.
  • Problem: Fluctuating temperature readings.
    • Solution: Use a capacitor in parallel with the thermistor to stabilize the readings.

FAQ 

Q1: Can I use other analog temperature sensors with this setup?
A1: Yes, any analog sensor can be connected to the MCP3008, including other types of temperature sensors.

Q2: How can I improve the accuracy of the temperature readings?
A2: You can improve accuracy by using a more precise thermistor and refining the temperature calculation formula based on the thermistor’s datasheet.

Conclusion 

In this project, you learned how to measure temperature using a thermistor and MCP3008 ADC on a Raspberry Pi. By reading the thermistor’s analog signal and converting it to a temperature value, you have created a simple and effective temperature monitoring system. This project introduces the basics of Measuring Temperature with a Thermistor on Raspberry Pi and can be expanded for more complex applications like data logging or home automation.

Post Views: 7